Page 101 of 124 FirstFirst ... 519196979899100101102103104105106111 ... LastLast
Results 2,001 to 2,020 of 2468
  1. Keegsta's Avatar
    Posts
    198 Posts
    Global Posts
    209 Global Posts
    #2001  
    Did anyone else get this same error when installing on 1.4.1?

    root@palm-webos-device: sh /var/home/root/800MHzOS14.sh install
    tar: Removing leading `/' from member names
    crypto/ecb.ko
    crypto/pcbc.ko
    drivers/block/nbd.ko
    drivers/net/ifb.ko
    drivers/scsi/scsi_wait_scan.ko
    arch/arm/oprofile/oprofile.ko
    tar: arch/arm/oprofile/oprofile.ko: Wrote only 3584 of 10240 bytes
    arch/arm/boot/uImage
    tar: Error exit delayed from previous errors
    sed: write error
    Rebooting...
    Drove 3 hours to buy my Palm Pre on day one.
  2. PreGk's Avatar
    Posts
    441 Posts
    Global Posts
    631 Global Posts
    #2002  
    Quote Originally Posted by crxssi View Post
    I doubt the phone "rebooted", it probably restarted Luna (a phone reboot will take several minutes, a Luna restart will take around 1 min or less). I have been having problems with occasional Luna restarts ever since 1.4.0, and it (unfortunately) continues with 1.4.1.1. It doesn't seem to matter if the 800 Mhz kernel is installed or not. Prior to 1.4.0, I had been using the phone almost 9 months and never had a spontaneous Luna restart (or reboot for that matter).
    No it definitely rebooted (full restart). I know the difference. It took a few minutes to boot up, I was actually staring at the "non-glowing" Palm logo considering pulling the battery, but I let it run its course and it eventually booted.
  3. PreGk's Avatar
    Posts
    441 Posts
    Global Posts
    631 Global Posts
    #2003  
    Quote Originally Posted by caj2008 View Post
    600 ipk is different and is fine. Your problems are not related to this ipk. A lunasysmgr patch is totally different than a kernel. This thread is referring only to use of 720 and 800 MHz kernel.
    Ok Caj, I think I may have missed my point. I wanted to know the user reported issues with the 720/800 kernel on 1.4.1, so I can lookout for them and determine if I have experienced them already (without the 720/800 kernel installed) to see if they may be unrelated to the kernel and maybe related to 1.4.1.
  4. #2004  
    Quote Originally Posted by Keegsta View Post
    Did anyone else get this same error when installing on 1.4.1?

    root@palm-webos-device: sh /var/home/root/800MHzOS14.sh install
    tar: arch/arm/oprofile/oprofile.ko: Wrote only 3584 of 10240 bytes
    arch/arm/boot/uImage
    tar: Error exit delayed from previous errors
    sed: write error
    Rebooting...
    Yikes! It would appear that you either ran out of disk space (Flash space) or your .sh file was corrupt or truncated. I hope it didn't frakk your phone, since you might end up with some files from the old kernel and some from the new!

    Really, for something this important, md5sums should be posted for the files to verify the are correct first (or do these shar files have some self-validation first, before untarring?)
    The power behind WebOS (and Android, and Maemo, and Google itself) is Linux!
  5. #2005  
    hey caj, can you describe some of the issues others have come across on 1.4.1?
  6. PreGk's Avatar
    Posts
    441 Posts
    Global Posts
    631 Global Posts
    #2006  
    Quote Originally Posted by caj2008 View Post
    If you had an issue and it cleared up after unistall, could you reinstall to verify if the problem resurfaces.
    If that's directed at me, I'm installing the 720Mhz Kernel as we speak. As far as crashing with the 600 .ipk, I don't blame the patch at all. I think it was more related to the heavy load I was putting on my Pre (BT streaming seems to really bog down the Pre). Sorry if I made it sound like the patch caused it.
  7. #2007  
    whats the best way to check if the 800 is working on the phone?
  8. #2008  
    Quote Originally Posted by biggamer3 View Post
    whats the best way to check if the 800 is working on the phone?
    lol... see step 11 in the OP


    caj, I couldn't take 500Mhz anymore... you spoiled me rotten. Just re-installed the 800Mhz kernel, i'll report back if i have any issues on 1.4.1.1
  9. PreGk's Avatar
    Posts
    441 Posts
    Global Posts
    631 Global Posts
    #2009  
    Quote Originally Posted by biggamer3 View Post
    whats the best way to check if the 800 is working on the phone?
    Read the first post. You have to type in a command in WOSQI
  10. Keegsta's Avatar
    Posts
    198 Posts
    Global Posts
    209 Global Posts
    #2010  
    Quote Originally Posted by crxssi View Post
    Yikes! It would appear that you either ran out of disk space (Flash space) or your .sh file was corrupt or truncated. I hope it didn't frakk your phone, since you might end up with some files from the old kernel and some from the new!

    Really, for something this important, md5sums should be posted for the files to verify the are correct first (or do these shar files have some self-validation first, before untarring?)
    Any suggestions on how to fix it?
    Drove 3 hours to buy my Palm Pre on day one.
  11. #2011  
    still waiting to update so i can keep my 800 patch
  12. #2012  
    +1
  13. Keegsta's Avatar
    Posts
    198 Posts
    Global Posts
    209 Global Posts
    #2013  
    Wow, so after this error when trying to uninstall the patch:

    root@palm-webos-device: sh /var/home/root/800MHzOS14.sh uninstall
    boot/uImage-2.6.24-palm-joplin-3430
    lib/modules/2.6.24-palm-joplin-3430/
    lib/modules/2.6.24-palm-joplin-3430/tisgxgfx/
    lib/modules/2.6.24-palm-joplin-3430/tisgxgfx/bc_example.ko
    tar: lib/modules/2.6.24-palm-joplin-3430/tisgxgfx/bc_example.ko: Wrote only 4096 of 6656 bytes
    lib/modules/2.6.24-palm-joplin-3430/tisgxgfx/pvrsrvkm.ko
    lib/modules/2.6.24-palm-joplin-3430/tisgxgfx/omaplfb.ko
    tar: lib/modules/2.6.24-palm-joplin-3430/modules.ofmap
    lib/modules/2.6.24-palm-joplin-3430/tisgxgfx/omaplfb.ko: Wrote only 5632 of 9416 bytes
    lib/modules/2.6.24-palm-joplin-3430/drivers/
    lib/modules/2.6.24-palm-joplin-3430/drivers/misc/
    lib/modules/2.6.24-palm-joplin-3430/drivers/misc/exmap.ko
    lib/modules/2.6.24-palm-joplin-3430/modules.symbols
    lib/modules/2.6.24-palm-joplin-3430/modules.seriomap
    lib/modules/2.6.24-palm-joplin-3430/modules.dep
    lib/modules/2.6.24-palm-joplin-3430/kernel/
    lib/modules/2.6.24-palm-joplin-3430/kernel/crypto/
    lib/modules/2.6.24-palm-joplin-3430/kernel/crypto/pcbc.ko
    lib/modules/2.6.24-palm-joplin-3430/kernel/crypto/ecb.ko
    lib/modules/2.6.24-palm-joplin-3430/kernel/drivers/
    lib/modules/2.6.24-palm-joplin-3430/kernel/drivers/net/
    lib/modules/2.6.24-palm-joplin-3430/kernel/drivers/net/ifb.ko
    lib/modules/2.6.24-palm-joplin-3430/kernel/drivers/scsi/
    lib/modules/2.6.24-palm-joplin-3430/kernel/drivers/scsi/scsi_wait_scan.ko
    lib/modules/2.6.24-palm-joplin-3430/kernel/drivers/block/
    lib/modules/2.6.24-palm-joplin-3430/kernel/drivers/block/nbd.ko
    lib/modules/2.6.24-palm-joplin-3430/kernel/net/
    lib/modules/2.6.24-palm-joplin-3430/kernel/net/wifi/
    lib/modules/2.6.24-palm-joplin-3430/kernel/net/wifi/sd8xxx.ko
    lib/modules/2.6.24-palm-joplin-3430/kernel/net/wifi/uap8xxx.ko
    lib/modules/2.6.24-palm-joplin-3430/kernel/arch/
    lib/modules/2.6.24-palm-joplin-3430/kernel/arch/arm/
    lib/modules/2.6.24-palm-joplin-3430/kernel/arch/arm/boot/
    lib/modules/2.6.24-palm-joplin-3430/kernel/arch/arm/boot/uImage
    lib/modules/2.6.24-palm-joplin-3430/kernel/arch/arm/oprofile/
    lib/modules/2.6.24-palm-joplin-3430/kernel/arch/arm/oprofile/oprofile.ko
    lib/modules/2.6.24-palm-joplin-3430/modules.ieee1394map
    lib/modules/2.6.24-palm-joplin-3430/modules.usbmap
    lib/modules/2.6.24-palm-joplin-3430/modules.alias
    lib/modules/2.6.24-palm-joplin-3430/dspbridge/
    lib/modules/2.6.24-palm-joplin-3430/dspbridge/bridgedriver.ko
    lib/modules/2.6.24-palm-joplin-3430/modules.isapnpmap
    lib/modules/2.6.24-palm-joplin-3430/modules.inputmap
    lib/modules/2.6.24-palm-joplin-3430/modules.pcimap
    lib/modules/2.6.24-palm-joplin-3430/modules.ccwmap
    usr/bin/LunaSysMgr
    tar: usr/bin/LunaSysMgr: Wrote only 3072 of 10240 bytes
    etc/event.d/PmNetConfigManager
    tar: Error exit delayed from previous errors
    Rebooting...

    My phone will no longer boot up.
    Drove 3 hours to buy my Palm Pre on day one.
  14. #2014  
    Quote Originally Posted by Menace187 View Post
    still waiting to update so i can keep my 800 patch
    +1

    I'm on Verizon, so it looks like it's going to be another couple weeks before I get it. I've reinstalled the 800MHz patch & disabled the auto update... I'll enable it & take the 800MHz off when it's annouced that Verizon is getting the update!
  15. PreGk's Avatar
    Posts
    441 Posts
    Global Posts
    631 Global Posts
    #2015  
    Ok, I'm back in action as well. I thought the 600 patch could hold me off for a couple days, but I was wrong. I'm at 720 again, and I hate using my Pre without it. Everything looks good so far, no more stutter on scrolling through the music collection. I'll report back if any issues.
  16. orizzle's Avatar
    Posts
    230 Posts
    Global Posts
    236 Global Posts
    #2016  
    Quote Originally Posted by Keegsta View Post
    My phone will no longer boot up.
    you have to doctor now
    Je fais ce que je veux avec mes cheveux!!! Sprint: Pre+ 2.1
  17. Keegsta's Avatar
    Posts
    198 Posts
    Global Posts
    209 Global Posts
    #2017  
    Quote Originally Posted by orizzle View Post
    you have to doctor now
    Is there any way I can get my pictures off of the USB drive?
    Drove 3 hours to buy my Palm Pre on day one.
  18. #2018  
    tried the 800 patch again with 1.4.1 and it seems fine no heat indication yet, I also am alpha testing the cpu scaler ultimate with the kernal and its very very nice, once its public it will be very helpful with every overclocking kernal.
  19. #2019  
    Quote Originally Posted by Keegsta View Post
    Wow, so after this error when trying to uninstall the patch:
    tar: Error exit delayed from previous errors
    Rebooting...

    My phone will no longer boot up.
    (It is not a patch, it is a replacement kernel)

    I was afraid of that. It looks like you will have to use the Dr. thing to restore your phone to factory defaults

    At least- look at the bright side- it should be nice a clean and ready to install the kernel again.

    Check the size and md5sum's of the downloaded files this time, firs. I have verified that both of these are working files:

    $ ls -l *sh
    -rw-rw-r-- 1 crxssi crxssi 3267933 2010-04-02 16:30 720MHzOS14.sh
    -rw-rw-r-- 1 crxssi crxssi 3267933 2010-03-28 21:11 800MHzOS14.sh

    $md5sum *sh
    a3e92a20566462618a9d6c63a36e670d 720MHzOS14.sh
    c0e33148b1b126666b97f88c5a3e4f39 800MHzOS14.sh
    The power behind WebOS (and Android, and Maemo, and Google itself) is Linux!
  20. #2020  
    when you doctor your files won't be affected. They changed how the doctor works now. It just replaces the system files that need to be changed.

Tags for this Thread

Posting Permissions