Page 2 of 2 FirstFirst 12
Results 21 to 38 of 38
  1. #21  
    ok i got it ebags333, i had to reboot my vista go figure.

    no the treo says

    "BL Image Backup"
    "Backup Successful"

    2 bars both full.

    now i just dont know how i should go about removing the sd card to see if it has a file on it for you. maybe me just yanking it is what caused the corrupt fs last time.
  2. #22  
    still asking to format. i beleive i have to use winhex to dump the file
  3. #23  
    Ok u do have to use winhex, im not sure what part of the raw disk image you need. it lookes like it starts with at the beginning and it is infact the boot loader because i can see some of the ascii
  4. #24  
    Ebags333 check your email. 5.02 boot loader sent.
  5. #25  
    does any one know how big the bootloader should be? as i ripped it from the raw disk image its 192kb
  6. #26  
    Its in RAW format, use "Open Disk" with winhex
    6b 6f 63 6f 6d 61 6e 20 6f 66 20 63 64 6d 61 2d 64 65 76 2d 74 65 61 6d
  7. #27  
    Did that file i sent you work out ebags333? also can any one give me a run down on the mtty commands to dump my nv so i can clonee my esn>
  8. #28  
    Quote Originally Posted by larryo108 View Post
    Install the Treo 650 bootloader drivers,
    Disable USB connections in ActiveSync
    remove the battery from your 700wx
    while holding down the side button, plug in hotsync cable,
    then reinstall bettery
    run mtty 1.42, and open the usb port. Set Data Bits from 8 to 7.
    then type "ram2sd boot"
    Slight but critical change to the instructions.
    http://discussion.treocentral.com/sh...&postcount=687

    I cant get the Treo 650 bootloader drivers to install, it tells me that they are unsigned and do not give me a choice to install any way. I am running Windoze XP SP3 on an Acer 5920.

    any ideas?
    <img src="http://img231.imageshack.us/img231/9343/scifinerd7jo.jpg" border="0">
    <img src="http://img109.imageshack.us/img109/9600/pirateuserbar3mz.jpg" border="0">
  9. #29  
    Quote Originally Posted by aenigma View Post
    http://discussion.treocentral.com/sh...&postcount=687

    I cant get the Treo 650 bootloader drivers to install, it tells me that they are unsigned and do not give me a choice to install any way. I am running Windoze XP SP3 on an Acer 5920.

    any ideas?
    force install through the device manager
  10. #30  
    Quote Originally Posted by Juggalo_X View Post
    force install through the device manager
    http://discussion.treocentral.com/sh...&postcount=687

    When I plug the device in does it does NOT get detected in the hardware profile. So how do I Force Install through the Device Manager?
    <img src="http://img231.imageshack.us/img231/9343/scifinerd7jo.jpg" border="0">
    <img src="http://img109.imageshack.us/img109/9600/pirateuserbar3mz.jpg" border="0">
  11. #31  
    Quote Originally Posted by aenigma View Post
    http://discussion.treocentral.com/sh...&postcount=687

    When I plug the device in does it does NOT get detected in the hardware profile. So how do I Force Install through the Device Manager?
    if it does not detect there is no point ot force install. because the computer cannot see the treo anyhow.
  12. #32  
    Quote Originally Posted by Juggalo_X View Post
    if it does not detect there is no point ot force install. because the computer cannot see the treo anyhow.
    I have moved my issue to its own thread, here: http://discussion.treocentral.com/sh...97&postcount=1
    <img src="http://img231.imageshack.us/img231/9343/scifinerd7jo.jpg" border="0">
    <img src="http://img109.imageshack.us/img109/9600/pirateuserbar3mz.jpg" border="0">
  13. #33  
    Ebags: im doing some experimenting. what BL version are you and would u mind dumping yours for me?

    ebags im stuck on Blue 3.01 like you were how did you fix this?
    Last edited by Juggalo_X; 07/10/2008 at 01:14 PM.
  14. #34  
    never mind im force flashing it right now.

    woooooo scary stuff. i got it all back and running on boot 5.02

    i think its impossible to brick these things lol
    Last edited by Juggalo_X; 07/10/2008 at 02:26 PM.
  15. lennysh's Avatar
    Posts
    19 Posts
    Global Posts
    20 Global Posts
    #35  
    i beg to differ... mines bricked... But I can still do lots of commands, just will not boot into WM!
    If I have helped you in any way, and you wish to Donate, you can click here!

    Chat Rooms:
    Website: Java or IRC Client
    PPCGeeks: Java or IRC Client
    XDA-Devs: Java or IRC Client
  16.    #36  
    Quote Originally Posted by lennysh View Post
    i beg to differ... mines bricked... But I can still do lots of commands, just will not boot into WM!

    Random necro?
  17. #37  
    Quote Originally Posted by lennysh View Post
    i beg to differ... mines bricked... But I can still do lots of commands, just will not boot into WM!
    Hmm... how is this even possible? It seems like if you can do any commands then you should be able to re-flash to a working version of WM, unless, of course, you've got some sort of hardware issue.
  18.    #38  
    Quote Originally Posted by westronic View Post
    Hmm... how is this even possible? It seems like if you can do any commands then you should be able to re-flash to a working version of WM, unless, of course, you've got some sort of hardware issue.
    I had a phone that did the same exact thing. It appears some sort of flag is being set that prevents it from booting. There's nothing in the boot loader to set/unset that flag (unfortunately).

    I reflashed the boot loader, firmware, and ROM multiple times using multiple methods. I wiped the NV. I did everything I could think of short of resorting to dark conjuring. Nothing I tried worked (unfortunately).

    The phone is still good and everything seems correct...it just won't boot.
Page 2 of 2 FirstFirst 12

Posting Permissions