Results 1 to 16 of 16
  1.    #1  
    I'm trying to install the 800 mhz patch but I'm having issues. I'm running 1.4 and have preware and everything and my pre is in the developers mode. However when I'm trying to install the 800 mhz patch using quickinstall I'm getting an error.

    I'm on step 6 of the official patch guide. When I'm trying to send the 800mhzos14.sh patch to /var/home/root I'm getting the following error:

    Command: put file:///var/home/root/800mhzos14.sh
    Reply: file open failed

    Anyone has an idea what's going on? Please help.

    My quickinstal is working correctly, I just installed a homebrew app through it.
  2. #2  
    try 800MHzOS14.sh install it might be case sen
  3.    #3  
  4. #4  
    you're not installing at this step, just putting the install file in the root user's home folder...

    a better way to do it is just put it on the Pre usb drive then terminal or ssh into it, go to /media/internal folder, and run it from there.
  5.    #5  
    Here is what I got:

    root@palm-webos-device: sh /media/internal/800MHzOS14.sh install
    tar: Removing leading `/' from member names
    crypto/ecb.ko
    crypto/pcbc.ko
    drivers/block/nbd.ko
    drivers/net/ifb.ko
    drivers/scsi/scsi_wait_scan.ko
    arch/arm/oprofile/oprofile.ko
    arch/arm/boot/uImage
    Rebooting...
    root@palm-webos-device:

    Now My pre is rebooting, hopefully I didn't brick it
  6. #6  
    Quote Originally Posted by Ayasinskiy View Post
    Are you using the latest WebOS Quick Install?
    Arthur Thornton

    Former webOS DevRel Engineer at Palm, HP, and LG
    Former webOS app developer (built Voice Memos, Sparrow, and several homebrew apps and patches)
    Former blogger for webOS Nation and webOS Roundup
  7. #7  
    Quote Originally Posted by Ayasinskiy View Post
    Here is what I got:

    root@palm-webos-device: sh /media/internal/800MHzOS14.sh install
    tar: Removing leading `/' from member names
    crypto/ecb.ko
    crypto/pcbc.ko
    drivers/block/nbd.ko
    drivers/net/ifb.ko
    drivers/scsi/scsi_wait_scan.ko
    arch/arm/oprofile/oprofile.ko
    arch/arm/boot/uImage
    Rebooting...
    root@palm-webos-device:

    Now My pre is rebooting, hopefully I didn't brick it
    That is what it is supposed to say. You did not brick it. It will perform amazingly when it boots.

    After it boots, run this command:

    Code:
    cat /proc/cpuinfo
    and you will see about the 3rd line from the top that it says the speed is about 796MHz. That is proof it is running at the 800MHz.

    If it says about 600MHz, then remove the patch and reinstall it and it should be fine.
    Arthur Thornton

    Former webOS DevRel Engineer at Palm, HP, and LG
    Former webOS app developer (built Voice Memos, Sparrow, and several homebrew apps and patches)
    Former blogger for webOS Nation and webOS Roundup
  8.    #8  
    Sweet!!!!!! I think it worked, here is what I got:

    root@palm-webos-device: cat /proc/cpuinfo
    Processor : ARMv7 Processor rev 3 (v7l)
    BogoMIPS : 796.91
    Features : swp half thumb fastmult vfp edsp
    CPU implementer : 0x41
    CPU architecture: 7
    CPU variant : 0x1
    CPU part : 0xc08
    CPU revision : 3
    Control reg : 0xc5387f
    Aux control reg : 0x42
    L1 instruction cache:
    features : read-alloc
    size : 16 KB
    assoc : 4
    line length : 64
    sets : 64
    L1 data cache:
    features : write-through write-back read-alloc
    size : 16 KB
    assoc : 4
    line length : 64
    sets : 64
    L2 unified cache:
    features : write-through write-back read-alloc write-alloc
    size : 256 KB
    assoc : 8
    line length : 64
    sets : 512
    Cache LoC : 2
    Cache LoU : 1
    root@palm-webos-device:
  9. ChillHill's Avatar
    Posts
    84 Posts
    Global Posts
    85 Global Posts
    #9  
    yup youre good
  10.    #10  
    OMG this phone is so fast now I can't believe it. Thanks everyone for helping me with this patch. I'm surfing gizmodo (I know they hate on palm often), engadget and digg and lighting speeds. I can't believe how fast my pre has become. I can now actually scroll through those 3 websites really quick where as before if I have a single of those pages loaded it wouldn't scroll nearly as fast. I'm very impressed, this patch is amazing. I just hope I'm not going to burn out my cpu any time soon
  11. #11  
    I keep getting "permission denied" after I hit enter on the install. Any ideas?
  12. #12  
    are you logged in as root?
  13. #13  
    I don't know, how do you do that?
  14. #14  
    I am using webos quick install v3.02
  15. #15  
    i get the same error permission denied
  16. #16  
    read this thread from the top?? don't use WebOS Quick Install...

Posting Permissions